ISO 286-2 / IS 919 Part 2

Bright bar tolerances: h9, h10 and h11

The tolerance class is the second most important thing on a bright bar order after the grade, and the one most often left off. Full tables, plus what each class costs you.

Quick answer

Bright bar tolerance classes come from ISO 286-2, adopted in India as IS 919 Part 2. The lower case h means the upper deviation is zero, so the bar is never over nominal size. h9 is tightest and normally requires grinding, h10 suits turned and peeled bars, and h11 is the usual commercial class for cold drawn bar. At 20 mm nominal, h9 allows 0.052 mm, h10 0.084 mm and h11 0.130 mm, all below nominal.

Reading the class

What h9, h10 and h11 actually mean

The letter sets the position

Lower case letters are shaft tolerances, upper case are holes. For h, the upper deviation is zero. The bar is at nominal size or under it, never over. That is the whole point: an h-class bar will always enter a nominal-sized hole.

The number sets the width

The number is the ISO IT grade. A lower number is a narrower band. IT9 at 20 mm is 0.052 mm wide, IT11 at the same size is 0.130 mm. The band widens as the bar gets bigger, because the same relative accuracy is harder to hold.

Together they give limits

So a 20 mm bar ordered to h9 may measure anywhere from 19.948 mm to 20.000 mm and still be correct. Ordered to h11 it may measure 19.870 mm to 20.000 mm. Same nominal size, very different parts.

20 mm h9 → 20.000 / 19.948 mm  ·  20 mm h10 → 20.000 / 19.916 mm  ·  20 mm h11 → 20.000 / 19.870 mm
ISO 286-2 / IS 919 Part 2

Shaft tolerance table, h6 to h12

Deviations in millimetres, upper deviation zero. Read down to your bar size and across to the class you need.

Nominal size (mm)h6h7h8h9h10h11h12
over 1 to 30 / −0.0060 / −0.0100 / −0.0140 / −0.0250 / −0.0400 / −0.0600 / −0.100
over 3 to 60 / −0.0080 / −0.0120 / −0.0180 / −0.0300 / −0.0480 / −0.0750 / −0.120
over 6 to 100 / −0.0090 / −0.0150 / −0.0220 / −0.0360 / −0.0580 / −0.0900 / −0.150
over 10 to 180 / −0.0110 / −0.0180 / −0.0270 / −0.0430 / −0.0700 / −0.1100 / −0.180
over 18 to 300 / −0.0130 / −0.0210 / −0.0330 / −0.0520 / −0.0840 / −0.1300 / −0.210
over 30 to 500 / −0.0160 / −0.0250 / −0.0390 / −0.0620 / −0.1000 / −0.1600 / −0.250
over 50 to 800 / −0.0190 / −0.0300 / −0.0460 / −0.0740 / −0.1200 / −0.1900 / −0.300
over 80 to 1200 / −0.0220 / −0.0350 / −0.0540 / −0.0870 / −0.1400 / −0.2200 / −0.350
over 120 to 1800 / −0.0250 / −0.0400 / −0.0630 / −0.1000 / −0.1600 / −0.2500 / −0.400
over 180 to 2500 / −0.0290 / −0.0460 / −0.0720 / −0.1150 / −0.1850 / −0.2900 / −0.460

Values are the standard ISO 286-2 shaft deviations, reproduced as a buyer reference. For sizes above 250 mm or for letter classes other than h, consult the standard.

Which class to order

Matching the class to the process

In practice the finishing process and the tolerance class go together. Asking for h9 on a drawn bar means asking for a grinding operation, whether or not the enquiry says so.

ProcessUsual classWhat it suits
Cold drawn roundh10 / h11General machining stock, parts that will be turned anyway
Cold drawn hex and squareh11Nuts, fittings, keys, up to and including 80 mm
Turned and peeledh10Larger diameters, induction hardened parts
Centreless groundh9Sliding and sealing surfaces, shafts used as-supplied
Precision groundh6 / h7Spindles and locating diameters, usually by agreement

Three ways tolerance goes wrong on an order

  • Specifying h9 out of habit. If the part is turned down afterwards, the incoming class barely matters and you are paying for grinding you will machine away.
  • Leaving the class off entirely. The supplier will quote their commercial standard, usually h11, and the bar will be correct but possibly not what the drawing assumed.
  • Reading the band as plus or minus. h-class is all minus. A 20 mm h11 bar at 19.90 mm is in specification, and a collet sized for exactly 20.00 mm will not grip it properly.
How IS 9550 assigns these classes
FAQ

Common questions

What does h9 mean on a bright bar?

h9 is an ISO 286 shaft tolerance class. The lower case h means the upper deviation is zero, so the bar is never above nominal size, and the number sets the width of the tolerance band. A 20 mm bar to h9 is 20.000 mm to 19.948 mm.

What is the difference between h9, h10 and h11?

Only the width of the tolerance band. h9 is tightest, h11 is loosest. At 20 mm nominal, h9 allows 0.052 mm, h10 allows 0.084 mm and h11 allows 0.130 mm, all of it below nominal size.

Which tolerance class is standard for cold drawn bright bar?

h11 is the usual commercial class for cold drawn round, square and hexagonal bar. Turned and peeled bars are normally h10 and ground bars h9.

Why is the tolerance always minus and never plus?

Because h is a shaft tolerance class and its upper deviation is defined as zero. The bar can be at nominal size or under it, never over. That is what lets it enter a hole or a collet of nominal size.

Does a tighter tolerance cost more?

Yes. h9 normally needs a grinding operation after drawing or peeling, which is an extra process and an extra yield loss. Specify the class your part actually needs rather than the tightest available.

Is ISO 286 the same as IS 919?

IS 919 (Part 2) is the Indian Standard for the ISO system of limits and fits, and is technically equivalent. IS 9550 calls up tolerance classes by reference to IS 919 (Part 2).

Request a quote

Tell us the grade, size and quantity.

Send your requirement and our team will reply with availability and a quotation. Share a drawing if you have one.